Gowoops 2 PCS DHT22 Temperature Humidity Sensor Module Digital Measurement for Arduino Raspberry Pi 2 3

P>operate voltage: dc 3~5. 5v. P>please choose the original seller: Gowoops, we don't guarantee the quality of the products bought from other seller. P>temperature range: -40 ℃ ~ 80 ℃， humidity Range: 0~100%RH. User manual: http://osoyoo. Com/?p=15718specification:type: dhT22 temperature and humidity sensorOperate Voltage: DC 3~5.

5vsignal output type: digitaltemperature range: -40 ℃ ~ 80 ℃Temperature Measurement Accuracy: ± 05 ℃humidity range: 0~100%rhhumidity measurement accuracy: ± 2%RH Dimensions:Size: 40 x 15 x 9 mm L / W / HScrew hole diameter: 2. 6mmweight: 6gpackage included:2 x dhT22 Sensor Module2 x Cable P>with fixing screw hole, convenient for install and fixed.

P>single-bus digital signal output, bidirectional serial data.

---

Makerfocus 2pcs ESP8266 Module ESP-12E NodeMcu LUA WiFi Internet New Version Development Board

Data download access to the website: http://www. Nodemcu. Com test video: https://www. Youtube. Com/watch?v=Gh_pgqjfeQc. The chip model: cp2102; it is designed to occupy minimal PCB area; ESP8266 is a highly integrated chip designed for the needs of a new connected world. If you need more informations about it, pls refer to: https://www.

Amazon. Com/dp/b01n5aK6E1. How to email us? click "MakerFocus" and click "Ask a question". There is the way to guide you to use the new version: the command you needed to use is: esptool. Py --baud 115200 --port /dev/tty. Slab_usbtouart write_flash -fs 32m -ff 80m --flash_mode dio 0x00000 boot_v1. 7. Bin 0x1000 user1.

Bin 0x37c000 esp_init_data_default. Bin 0x37e000 blank. Bin the important part is "-flash mode dio" https://github. Com/espressif/esptool/wiki/SPI-Flash-Modes. Its high degree of on-chip integration allows for minimal external circuitry.


Similar products

---

HiLetgo 2pcs ESP8266 NodeMCU LUA CP2102 ESP-12E Internet WIFI Development Board Open source Serial Wireless Module Works Great with Arduino IDE/Micropython Pack of 2PCS

If you need more informations about it, pls refer to: https://www. Amazon. Com/dp/b01n5aK6E1. Built-in micro-usb, with flash and reset switches, easy to program. Its high degree of on-chip integration allows for minimal external circuitry. 4. Package included: 2* new version esp8266 nodemcu lua cp2102 WiFi Wireless Development Board Note: there are a batch of this item are the new grade version.

Set up your arduino ide as: go to file->preferences and copy the URL below to get the ESP board manager extensions: http://arduino. Esp8266. Com/stable/package_esp8266com_index. Json placing the http:// before the URL lets the Arduino IDE use it. Otherwise it gives you a protocol error. In arduino ide, look for the old fashioned Blink program.

Go to tools > board > board manager> Type "esp8266" and download the Community esp8266 and install. Load, compile and upload. Install the IDE 3. Full i/o port and wireless 802.


Similar products

---

JBtek BMP180 Barometric Pressure, Temperature and Altitude Sensor

Full i/o port and wireless 802. 11 supported, direct download no need to reset. How to email us? click "MakerFocus" and click "Ask a question". There is the way to guide you to use the new version: the command you needed to use is: esptool. Py --baud 115200 --port /dev/tty. Slab_usbtouart write_flash -fs 32m -ff 80m --flash_mode dio 0x00000 boot_v1.

7. Bin 0x1000 user1. Bin 0x37c000 esp_init_data_default. Bin 0x37e000 blank. Bin the important part is "-flash mode dio" https://github. Com/espressif/esptool/wiki/SPI-Flash-Modes. Firmware link: https://github. Com/nodemcu/nodemcu-firmware. Note: there are a batch of this item are the new grade version. Measure temperature, pressure, and altitude.

Its high degree of on-chip integration allows for minimal external circuitry. If you need more informations about it, pls refer to: https://www. Amazon. Com/dp/b01n5aK6E1. Arduino compatible, works great with the latest Arduino IDE/Mongoose IoT/Micropython.


Similar products

---

Haitronic 120pcs 20cm length Jumper Wires/dupont cable Multicolored10 color 40pin M to F, 40pin M to M, 40pin F to F for Breadboard/Arduino based/DIY/raspberry Pi 2 3/Robot Ribbon Cables Ki

Portable design, easy and safe to use. Including one 40-pin male to female jumper wires, one 40-pin male to male jumper wires, one 40-pin female to female jumper wires. 10 different colors, stepper motor 3d printer etc, 120units copper cable in total, for making prototypes with arduino boards, The combinations provide a jumper for whatever you need.

Its high degree of on-chip integration allows for minimal external circuitry. How to email us? click "MakerFocus" and click "Ask a question". There is the way to guide you to use the new version: the command you needed to use is: esptool. Py --baud 115200 --port /dev/tty. Slab_usbtouart write_flash -fs 32m -ff 80m --flash_mode dio 0x00000 boot_v1.

7. Bin 0x1000 user1. Bin 0x37c000 esp_init_data_default. Bin 0x37e000 blank. Bin the important part is "-flash mode dio" https://github. Com/espressif/esptool/wiki/SPI-Flash-Modes. Maybe there are some different between the new one and old one in the aspect of usage. Features: Ø color: 10 options as shown in the pictures.




Similar products

---

Diymall 0.96" Inch Yellow Blue I2c IIC Serial Oled LCD LED Module 12864 128X64 for Arduino Display Raspberry PI 51 Msp420 Stim32 SCR

How to email us? click "MakerFocus" and click "Ask a question". There is the way to guide you to use the new version: the command you needed to use is: esptool. Py --baud 115200 --port /dev/tty. Slab_usbtouart write_flash -fs 32m -ff 80m --flash_mode dio 0x00000 boot_v1. 7. Bin 0x1000 user1. Bin 0x37c000 esp_init_data_default.

Bin 0x37e000 blank. Bin the important part is "-flash mode dio" https://github. Com/espressif/esptool/wiki/SPI-Flash-Modes. White color link https://www. Amazon. Com/dp/b00o2kdqbeblue color link ://www. Amazon. Com/dp/b00o2lkew2 2pcs link https://www. Amazon. Com/dp/b01hebijkk resolution: 128x64 color: blue viewing angle: greater than 160 degrees Supported platforms: for arduino, STIM32 / 2, MSP430 series, 51 series, SCR chips Low power consumption: 0.

04w during normal operation Support wide voltage: 3. 3v-5v dc working temperature: -30-80 degrees Volume: 27MM * 27MM * 4. 1mm driver ic: ssd1306 communication: iic, only two i / o ports no font: The software takes word modulo Backlight: OLED self light, no backlight Interface: VCC: 3. 3-5v gnd: ground scl: serial clock sda: Serial Data Note: there are a batch of this item are the new grade version.




Similar products

---

Kuman 5PCS Soil Moisture Sensor Kit Compatible with Raspberry pi Arduino Uno R3 Mega 2560 with 10PIN Female to Female Jump Cables 20PIN Male to Female DuPont Jump Cable Automatic Watering System KY70

Makerfocus nrf24l01+ and esp8266 esp-01 breadboard breakout adapter board is come for free, it can compatible with nRF24L01+ and ESP8266 ESP-01. The example project of the soil moisture Sensor Module working with Arduino Uno R3 and Raspberry pi can be provided free by Email, please contact us via Amazon.

. The iic address can be changed, it is convenient to use with different machines. Firmware link: https://github. Com/nodemcu/nodemcu-firmware. Measure temperature, pressure, and altitude. Four square holes are easy to install. Kuman soil moisture module kit have 10pin female to female dupont cable and 20pin male to female DuPont cable for Raspberry pi 3 PI 2 RPI 1 model B+ B Arduino Uno R3 Mega 2560

Just peel off. Factory directly, 10 tiny copper wires inside of single jumper wire: high-level copper wire inside, durable for conductive connection. 0127mm, 36 awg/ single root, 20cm7. 87inch/axis; Standard 2. 54mm headers and sockets. Can be detached into120 single axis: 40 male-male, 40 male-female, 40 female-female.




Similar products

---

Vktech 5pcs 2M Waterproof Digital Temperature Temp Sensor Probe DS18b20

Makerfocus nrf24l01+ and esp8266 esp-01 breadboard breakout adapter board is come for free, it can compatible with nRF24L01+ and ESP8266 ESP-01. Data download access to the website: http://www. Nodemcu. Com. If you need more informations about it, pls refer to: https://www. Amazon. Com/dp/b01n5aK6E1. Perfect for your Arduino project.

9 ~ 12 adjustable resolution. Firmware link: https://github. Com/nodemcu/nodemcu-firmware. Storage temperature range: -55°c ~ - 125°C -67°F - +257°F. 10 different colors, 120units copper cable in total, stepper motor 3d printer etc, for making prototypes with arduino boards, The combinations provide a jumper for whatever you need.

Stainless steel tube size:Approx. 6*50mmdiameter*Length. Document link: https://drive. Google. Com/open?id=0b8dsgdar8_31uEItMmx6ZDJIOWs. The example project of the soil moisture Sensor Module working with Arduino Uno R3 and Raspberry pi can be provided free by Email, please contact us via Amazon. Built-in micro-usb, with flash and reset switches, easy to program.




Similar products

---

Diymall Bme280 Pressure Temperature Sensor Module with IIC I2c for Arduino

2pcs pack: https://www. Amazon. Com/dp/b01hezBOGC. Makerfocus nrf24l01+ and esp8266 esp-01 breadboard breakout adapter board is come for free, it can compatible with nRF24L01+ and ESP8266 ESP-01. Warranty: one year warranty, any question please feel free to contact. Data download access to the website: http://www.

Nodemcu. Com. How to email us? click "MakerFocus" and click "Ask a question". There is the way to guide you to use the new version: the command you needed to use is: esptool. Py --baud 115200 --port /dev/tty. Slab_usbtouart write_flash -fs 32m -ff 80m --flash_mode dio 0x00000 boot_v1. 7. Bin 0x1000 user1. Bin 0x37c000 esp_init_data_default.

Bin 0x37e000 blank. Bin the important part is "-flash mode dio" https://github. Com/espressif/esptool/wiki/SPI-Flash-Modes. Connection: gy-bme280 arduino vin------vcc gnd------gnd scl------a5 sda------a4 package included: 1 X BME280 Pressure Temperature Sensor Note: there are a batch of this item are the new grade version.

Firmware link: https://github.


Similar products

---

Makerfocus 4pcs ESP8266 Esp-01 Serial Wireless Wifi Transceiver Module Compatible with Arduino

The chip model: cp2102; it is designed to occupy minimal PCB area; ESP8266 is a highly integrated chip designed for the needs of a new connected world. Any question please feel free to contact before negative feedback or review. Thanks. How to email us? click "MakerFocus" and click "Ask a question". High quality stainless steel tube encapsulation waterproof moistureproof prevent rust.

10 different colors, stepper motor 3d printer etc, for making prototypes with arduino boards, 120units copper cable in total, The combinations provide a jumper for whatever you need. How to email us? click "MakerFocus" and click "Ask a question". There is the way to guide you to use the new version: the command you needed to use is: esptool.

Py --baud 115200 --port /dev/tty. Slab_usbtouart write_flash -fs 32m -ff 80m --flash_mode dio 0x00000 boot_v1. 7. Bin 0x1000 user1. Bin 0x37c000 esp_init_data_default. Bin 0x37e000 blank. Bin the important part is "-flash mode dio" https://github. Com/espressif/esptool/wiki/SPI-Flash-Modes.


Similar products

---

HiLetgo New Version ESP8266 NodeMCU LUA CP2102 ESP-12E Internet WIFI Development Board Open source Serial Wireless Module Works Great with Arduino IDE/Micropython

If you receive different versions module， please carefully follow the pictures and youtube video to test. Esp8266 cp2102 nodemcu lua esp-12e wifi serial Wireless Module. Maybe there are some different between the new one and old one in the aspect of usage. Storage temperature range: -55°c ~ - 125°C -67°F - +257°F.

Output lead:red VCC, blackGND. Full i/o port and wireless 802. 11 supported, direct download no need to reset. Support 3 modes: ap, stA, AP + STA. In arduino ide, look for the old fashioned Blink program. Pls feel free to email us if you have any question about how to use the new vertion module. How to email us? click "MakerFocus" and click "Ask a question".

Here is a ds18b20 original chip, three fine copper wire temperature sensor. How to email us? click "MakerFocus" and click "Ask a question". There is the way to guide you to use the new version: the command you needed to use is: esptool. Py --baud 115200 --port /dev/tty. Slab_usbtouart write_flash -fs 32m -ff 80m --flash_mode dio 0x00000 boot_v1.

7.


Similar products